Bimota Tesi 1D 906 with wheel hub steering

Table of contents

Bimota Tesi 1D 906 with wheel hub steering
duke

counselor

technology & future

Bimota Tesi 1D 906 with wheel hub steering

Bimota Tesi 1D 906 with wheel hub steering
Ecstatic technology freaks all over the world

Why easy if complicated is another option? In the early 1990s, the small company Bimota proved that there are alternatives to the telescopic fork. The Tesi 1D 906 with wheel hub steering delighted technology freaks all over the world. Also editor-in-chief Michael Pfeiffer.

Michael Pfeiffer

01/21/2010

Yes, I admit I was one of them too. Like so many, I no longer believed in the telescopic fork in the early 1990s. It was just too limp in front for me with its two standpipes. How was such a windy construction supposed to curb the impetuous forward thrust of the athletes elite at the time? Absorbing braking forces, springs, transferring steering forces, damping? It would be much better to assign these tasks to appropriate specialists. How to separate wheel guidance and steering in a car. I euphorically tested everything that was knuckle-jointed in any way. Mostly do-it-yourself solutions, which usually showed pretty terrible driving behavior. How happy I was when I found out that the small Italian manufacturer Bimota would bring a series machine with a new type of front suspension. And how keen I was to drive this very machine. It had to be sensational: the Bimota Tesi 1D 906 was the bike of my dreams, and in my quiet room I imagined how this front wheel system would work. In the wheel hub there is a tubular steel cross, the vertical part of which forms the steering head, while the horizontal part is held by the two clamping fists of the front swing arm. The steering knuckle engages the wheel hub body, the two brake calipers are attached and the huge wheel bearings run on it. How is it steered? Two meters of pipe and a lot of levers and joints transfer the steering forces to the wheel hub. What a hassle! It just had to be better than a fork.

I got a foretaste of future tests on a beautiful summer day in Misano. Bimota test driver Gianluca Galasso moves out for a few quick laps on the Grand Prix track and chases the Tesi around corners like a madman. It’s unbelievable how weird the man drives, how late he can brake. That was the confirmation of the superiority of the new suspension technology, I was quite sure of that. Suddenly: violent scratching, two or three dull impacts – silence. The unlucky pilot stomps back to the pits. I can not believe it. “What happened?” Galasso grins: “Ingegnere Marconi wanted to know whether the front swing arm touched down when cornering, and I tried it. She doesn’t sit up. The wheels slip away beforehand. “Oh, yes. Pierluigi Marconi is Bimota’s chief engineer and he is in charge. He can be tested hard and also has the necessary hard tester.

Buy complete article

Bimota Tesi 1D 906 with wheel hub steering

final
Bimota Tesi 1D 906

6 pages) as PDF

€ 2.00

Buy now


Bimota Tesi 1D 906 with wheel hub steering


duke

Spectacular technology: the front wheel of the Tesi is also guided by a swing arm. The steering is located in the wheel hub and is guided to the handlebars via an elaborate linkage.

I’m allowed to answer a year later. Bimota importer Reinhold Kraft gives me a piece of high-tech that costs 61,420 marks. I am trembling with excitement. The starter starts the tuned Ducati four-valve Desmo with difficulty. There is a loud rumble from the pots that have barely been steamed. Funny, when you sit on it, you don’t see the Tesi’s strange front suspension at all. Bimota hides almost the entire chassis technology under a rather bulky full casing. But maybe that’s a good thing. Because then you don’t see the disturbing filigree braking torque supports and steering linkages. Just drive and enjoy. The striking handiness, the extreme braking stability, the strong pulling engine. At every stop I get astonished looks. Looks kind of crazy, the swingarm sticking out of the front panel. It is not without pride that I steer back and forth a little while standing. On the highway, and then it happens: The Tesi begins to lurch terribly, with 160 things so strong that the front tire squeaks. Has my last hour struck now? I come to a stop on a large motorway bridge. Everything is fixed in the front, also in the back, what happened? Reinhold Kraft frowns. “Maybe the tapered roller bearings have settled in the hub. We have to check that. ”I was already rid of the Bimota.

A week later, the same thing again. Whatever Reinhold and his workshop gurus have done, it works. I’m going to Hockenheim, I speed up the A3 to Cologne and back, I rub the tires down a lot, the Tesi still wobbles a bit. But that can be tolerated. The much too hard front shock absorber is not. I give the Tesi back with full respect for the constructive performance and the manual skills of the Bimota team. But a new world in terms of chassis did not open up to me. No, unfortunately not.


Bimota Tesi 1D 906 with wheel hub steering


duke

It’s unbelievable how weird the man could drive.

Yet. The separation of the suspension and steering is now a bestseller. I beg your pardon? Sure, of course! Telelever, BMW R 1200 GS and their relatives. The tubes transmit the steering forces, the swing arm the braking forces, and the shock absorber cushions and dampens. Works great. So I was right after all. At least a bit.

The Bimota Tesi has not been much more than an eye-catcher to this day. It was just too expensive for that. Bimota produced a total of 366 machines with the four-valve Ducati V2. And they probably all ended up in the hands of collectors. Good for those who have one with them.

Technical specifications


Bimota Tesi 1D 906 with wheel hub steering


duke

Powerful: aluminum plates milled from solid hold the Bimota together and take up the two wings. Arm on: Ducati engine.

Engine:
Two-cylinder four-stroke 90 degree V engine, four valves per combustion chamber, desmodromic control, bore x stroke 94 x 68 millimeters, 904 cm3, 83 kW (113 hp) at 8500 rpm, injection, electric starter, dry clutch, Six-speed gearbox, chain drive.

Landing gear:
Composite chassis made of aluminum carrier plates and steel lattice tube structure, wheel hub steering, aluminum swing arm front and rear, each with spring strut, steel steering linkage, braking torque support, double disc brake in front, disc brake in rear, cast wheels, tires 120/70 ZR 17 and 180/55 ZR 17.

Measurements and weight:
Wheelbase 1410 mm, caster 83 mm, seat height 775 mm, weight with a full tank of 213 kg, tank capacity 16 liters, top speed 235 km / h. Price 61,420 marks (1991)

Leave a Reply

Your email address will not be published. Required fields are marked *