Here’s how it works: All about chains

Table of contents

Here's how it works: All about chains
archive

accesories

Here’s how it works: All about chains

That’s how it’s done
Everything about chains

Lighter than a cardan shaft, cheaper than a toothed belt drive – the chain still has its place. And certain claims.

08/29/2007

Chain maintenance

Regular care and maintenance guarantee a long service life for motorcycle chains. An incorrectly set chain tension – regardless of whether it is too tight or too loose – inevitably leads to increased wear and is dangerous. Chains that are too loose can jump off the sprocket, and chains that are too tight not only damage the gearbox output bearing, but can even tear due to the extreme loads, especially during compression. It is therefore very important to regularly check the chain slack in accordance with the information in the manual. Also make sure that the rear axle is not crooked in the swing arm. Otherwise the chain would have to describe an arc, so to speak, which extremely accelerates wear. It is therefore essential to use the scales of the clamping devices in the swing ends equally. One of the less popular, but very useful maintenance measures is cleaning to protect the sealing rings from damage, which can ultimately lead to the loss of the permanent grease fillings. To use: Apply the chain cleaning agent available from specialist retailers from around four euros (300 ml can), rework with a paintbrush or brush and then wipe or hose off. Under no circumstances hold onto it with a steam jet. That would rinse out the grease fillings behind the sealing rings. The chain spray should be applied at the latest when the chain is dry (finger test). When spraying the chain: plenty on the inside, moderate on the outside. In addition, it is better to apply more frequently and sparingly than rarely and thickly.


Here's how it works: All about chains


archive

The chain slack is always measured with the driver seated.


Here's how it works: All about chains


archive

When spraying chain grease, work more generously on the inside than on the outside. Much does not help much, it is better to lubricate the chain more frequently and sparingly.

Chain locks

If you don’t feel like removing the swing arm when changing the chain, you should opt for an open chain with a lock, which can be installed much faster. The clip locks, which can be installed in a few seconds with the help of pliers, are suitable for the off-road sector, where the secondary ratios are often changed, and for low-performance motorcycles. Very important: the mounting direction of the clip. The closed side must point in the direction of movement of the chain so that the lock cannot open unintentionally while driving. This cannot happen with rivet locks, as they are inseparably riveted with the appropriate special tools (from around 150 euros). Different tools are required for the two different types of rivets, hollow rivets or solid rivets. While the hollow rivet is being expanded with a mandrel, the right tool for the solid rivet simply presses the head flat. Another locking technology are the patented screw locks. Compared to rivet locks, they can be attached without great effort with a suitable small wrench.


Here's how it works: All about chains


archive

Clip lock, screw lock and rivet lock (from left to right)


Here's how it works: All about chains


archive

Solid rivet / hollow rivet lock


Here's how it works: All about chains


archive

No special equipment is required for clip locks and screw locks, a riveting tool helps with the others (left, around 150 euros)

Chain set change

In contrast to the oil change, there is no clear specification in kilometers for the chain set as to when it should be replaced. How do you know whether the chain has reached or even exceeded its wear limit? There are several answers to this question. On the one hand, the adjustment mechanisms for the chain tension are located at the ends of the swing arms. When the markings have reached the end of the scale, it is high time for a new set of chains. However, this is already due when the sprocket has so-called shark teeth or the chain can be lifted off the chainring up to the tooth tips (see photos). Tips for changing chain sets: Always change the complete set, i.e. chain, pinion and sprocket. If only the chain is replaced, it will lengthen extremely quickly on the more or less heavily worn sprockets and pinions. First, with the chain in place and the rear wheel brake locked, loosen the screw connections of the pinion and chain wheel. To open the old chain, either use a cutting disc (“Flex”) or a special chain cutting tool (in specialist shops from around 10 euros). Before installing the new parts, to be on the safe side, compare the number of links in the chain and the number of teeth on the pinion and sprocket with those of the old parts. Then move the chain tensioner to the foremost position in order to facilitate the installation of the somewhat shorter chain, which is not yet worn. After installing the new pinion and the sprocket (use new lock washers or screw locks), mount the chain and close it with a clip, screw lock or rivet lock. Anyone who has opted for an endless chain has to accept the very time-consuming swing arm removal. At the very end, adjust the chain alignment and chain tension and check again after the first few kilometers.


Here's how it works: All about chains


archive

A chain cutting tool (costs between 10 and 30 euros) for opening and shortening is faster, quieter and usually less dangerous for a hobby screwdriver than the Flex.

Time to change: The markings on the chain tensioner (at the bottom), typical shark teeth on the sprocket (center) and a chain that can be pulled off (left) clearly indicate that the chain set is ready to be replaced.


Here's how it works: All about chains


archive


Here's how it works: All about chains


archive

  • Here’s how it works: mothballing

    archive counselor workshop Here’s how it works: mothballing Mothball the motorcycle Winter break If you don’t want to use your motorcycle for some time,…

  • Clean and maintain motorcycle chains

    archive accesories Clean and maintain motorcycle chains Advice: chain maintenance How do I properly care for the chain on my motorcycle?? Your…

  • This is how it works: motorcycle care

    accesories This is how it works: motorcycle care This is how it works: motorcycle care With these tips, your motorcycle will sparkle again as if it were…

  • Balancing motorcycle tires – this is how it works

    wolf 8th pictures wolf 1/8 Haweka balancing professional Uwe Westermann at the versatile Bike Boss Louis 2/8 Static yes, dynamic no: balancing stands…

  • Dainese Custom Works customization ex works

    Dainese 17th pictures Dainese 1/17 With Custom Works, the Italian motorcycle clothing manufacturer Dainese is now presenting a service for the individual…

  • Chain locks

    counselor workshop Chain locks Chain locks Chain locks In most cases, it is a hell of a job to replace an endless chain: remove the rear wheel, loosen…

  • This is how it works: Replace the seat

    Bilski counselor workshop This is how it works: Replace the seat That’s how it’s done Renew the seat Come on: shift your frustration to your old bank….

  • Report: Portrait of the Ducati works driver Cal Crutchlow

    Wood 11 pictures Gold and Goose Photography 1/11 Someone like Cal Crutchlow spends the whole year flying around the world in business class, puts a…

  • Ducati Multistrada V4 with Akrapovic exhaust ex works

    Ducati 45 pictures Ducati 1/45 Ducati brings the new Multistrada with a V4 engine. Ducati 2/45 Ducati has made the Multistrada even more versatile….

  • Change chain set

    counselor workshop Change chain set Change chain set Replace the pinion, toothed wheel and drive chain Regular chain maintenance can delay the moment of…

Leave a Reply

Your email address will not be published. Required fields are marked *